会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 2. 发明公开
    • TORQUE SENSOR
    • 扭矩传感器
    • EP2420810A1
    • 2012-02-22
    • EP10764540.0
    • 2010-04-16
    • Amiteq Co., Ltd.
    • GOTO, AtsutoshiYUASA, YasuhiroSAKAMOTO, HiroshiGOTO, Daisuke
    • G01L3/10B62D5/04
    • B62D6/10B62D5/049G01L3/105G01L25/003
    • An excitation AC signal biased by a predetermined DC voltage is applied to a coil to allow a DC voltage component in a coil output signal to contain failure information about disconnection, partial disconnection, or the like of the coil. The DC voltage component contained in the coil output signal is detected, and the detected DC voltage is provided as an offset voltage for a failure diagnosis. Further, to check a peak level of the excitation AC voltage, a DC voltage corresponding to the peak level may be contained in the offset voltage. A differential amplifier circuit for obtaining a difference between a coil detection output AC voltage component and a reference AC voltage component outputs an obtained differential signal offset by the offset voltage. Accordingly, the differential signal containing the offset voltage as the failure information is transmitted to a circuit for torque measurement as a torque detection signal via a single output line. The circuit for torque measurement provides the torque detection data based on the transmitted differential signal and at the same time extracts the offset voltage to use it for the failure diagnosis.
    • 由预定的直流电压偏置的激励交流信号被施加到线圈,以允许线圈输出信号中的直流电压分量包含关于线圈的断开,部分断开等的故障信息。 包含在线圈输出信号中的DC电压分量被检测,并且检测到的DC电压被提供作为用于故障诊断的偏移电压。 此外,为了检查激励AC电压的峰值电平,可以在偏移电压中包含对应于峰值电平的DC电压。 用于获得线圈检测输出AC电压分量与参考AC电压分量之间的差值的差分放大器电路输出所获得的差分信号,所述差分信号偏移了所述偏移电压。 因此,包含作为故障信息的偏移电压的差分信号经由单个输出线路被传输到用于转矩测量的电路,作为转矩检测信号。 转矩测量电路根据发送的差分信号提供转矩检测数据,同时提取偏置电压以用于故障诊断。
    • 4. 发明公开
    • POSITION SENSOR
    • 位置传感器
    • EP1898185A1
    • 2008-03-12
    • EP06767253.5
    • 2006-06-23
    • Amiteq Co., Ltd.
    • GOTO, Atsutoshi
    • G01D5/245
    • G01D5/2013G01D5/2216H02K11/225H02K24/00
    • A plurality of layers of flat coils (L41 - L46) are stacked and connected in series with each other to form a single coil pole (L4), and the coil pole is energized by an A.C. signal. Magnetism responsive member, provided to be opposed to the coil pole in a non-contact manner, is displaced relative to the coil pole, so that correspondency, to the coil section, of the magnetism-responsive member varies in response to variation in the relative position and thus impedance variation occurs in the coil pole. Position detection signal is provided on the basis of an output signal, responsive to the impedance variation, taken out from the coil pole.
    • 多层扁平线圈(L41-L46)堆叠并彼此串联以形成单个线圈极(L4),并且线圈极由A.C.信号激励。 设置成与线圈极非接触地相对的磁响应构件相对于线圈极移位,使得响应于磁性响应构件的线圈部的相对于相对于线圈极的相对变化而变化 位置,从而在线圈极发生阻抗变化。 根据输出信号提供位置检测信号,响应从线圈极取出的阻抗变化。