会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 1. 发明专利
    • Swash plate type compressor
    • 洗板式压缩机
    • JPS5749081A
    • 1982-03-20
    • JP12503280
    • 1980-09-09
    • Taiho Kogyo Co LtdToyoda Autom Loom Works Ltd
    • HATSUTORI MITSUHIROOONO HIROMITSUTAKENAKA KENJITAKAHASHI JIYUUMEI
    • F04B27/08F04B25/04F04B39/00
    • F05C2201/906F05C2203/086F05C2253/12
    • PURPOSE: To prevent seizure of sliding elements for transmitting the driving force of a swash plate to a piston even if the lubricating conditions are severe, by shaping the flat part of the substantially spherical sliding elements to have a slightly convex curvature.
      CONSTITUTION: In a swash plate type compressor shown in the Fig, a flat portion 10b of each spherical sliding element 10 is shaped to have a slightly convex, smoothly curved surface 10c having an extremely large radius of curvature, so that the height H
      1 is less than 15μm. Since, with such an arrangement, a wedge-shaped clearance, having an extremely small wedge angle that is decreased gradually in a smooth manner, is formed between the curved surface 10c of the sliding element 10 and the surface of a swash plate 8, lubricating oil attached to the surface of the swash plate 8 is readily drawn into the clearance at the time of high-speed operation, so that a film of lubricating oil for preventing direct contact between them is formed. Further, since the contact point of the swash plate 8 and curved surface 10c is changed for each rotation along with swinging motion of the sliding elements 10 and the amount of lubricating oil circulated is increased resultantly, so that the lubricating conditions can be further improved. Thus, it is enabled to protect the sliding elements 10 against seizure.
      COPYRIGHT: (C)1982,JPO&Japio
    • 目的:为了防止滑动元件发生旋转斜盘驱动力传递到活塞,即使润滑条件严重,通过使基本上球形的滑动元件的平坦部分成形为具有略微凸起的曲率。 构成:在图1所示的斜盘式压缩机中,每个球形滑动元件10的平坦部分10b成形为具有非常大的曲率半径的略凸出的平滑曲面10c,使得高度H1较小 超过15mum。 由于通过这种布置,在滑动元件10的弯曲表面10c和斜盘8的表面之间形成楔形间隙,该楔形间隙具有以平滑方式逐渐减小的非常小的楔角,并且润滑 附着在旋转斜盘8的表面上的油容易地在高速运转时被拉入间隙,从而形成用于防止它们之间直接接触的润滑油膜。 此外,由于斜盘8和曲面10c的接触点随着滑动元件10的摆动而随着每个旋转而改变,所以循环的润滑油的量增加,从而可以进一步提高润滑条件。 因此,能够保护滑动元件10免受卡住。
    • 2. 发明专利
    • Swash-plate type compressor
    • 冲压式压缩机
    • JPS5751977A
    • 1982-03-27
    • JP12643280
    • 1980-09-11
    • Taiho Kogyo Co LtdToyoda Autom Loom Works Ltd
    • HATSUTORI MITSUHIROOONO HIROMITSUTAKENAKA KENJITAKAHASHI JIYUUMEI
    • F04B27/08F04B25/04
    • F05C2201/906F05C2203/086F05C2253/12
    • PURPOSE: To stably prevent seizure by forming the flat surface area of a slider into convex surface and forming the chamfered areas each having different inclination angle in two steps on the outer peripheral edge of the flat surface area.
      CONSTITUTION: The flat surface area 10b of a slider 10 is formed into the convex surface 10c having the height 10μm or less and having an exceedingly large radius of curvature, having the center area of the flat surface area as apex, and the chamfered areas having the inclination angles of 1W45° and 0.5W1.5° for the flat surface area 10b are formed in two steps on the outer peripheral edge of the flat surface area 10b. Therefore, the scattering of seizure preventing effect reduces markedly, and seizure can be prevented stably.
      COPYRIGHT: (C)1982,JPO&Japio
    • 目的:通过将滑块的平坦表面积形成凸面来稳定地防止咬合,并且在平坦表面区域的外周边缘上形成两个具有不同倾斜角的倒角区域,两个阶梯形状。 构成:滑块10的平坦表面区域10b形成为具有10mum以下的高度的凸面10c,并且具有非常大的曲率半径,其平面面积的中心面积为顶点,并且倒角面积为 倾斜角度为1-45度。 和0.5-1.5度。 平坦面区域10b在平坦面区域10b的外周缘上形成为两个台阶。 因此,防止发作效果的飞散性显着降低,可以稳定地防止发作。