会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 52. 发明授权
    • Process and apparatus for preheating coking coal
    • 预炼炼焦煤的工艺和设备
    • US4251207A
    • 1981-02-17
    • US14977
    • 1979-02-26
    • Kurt-Gu_nther BeckGeorg PollertWolfgang Rohde
    • Kurt-Gu_nther BeckGeorg PollertWolfgang Rohde
    • C10B57/10C10B57/08F26B3/08
    • C10B57/08
    • Coking coal is preheated and dried by passing hot carrier gas into a generally vertical flash drying pipe, then passing comminuted coal into the same pipe, the carrier gas being blown with a flow speed to move the coal upwards in the pipe and passing at about the midpoint of the pipe a mixture of hot combustion gases and additional hot recycle gas branched off from the other hot waste gas line into the pipe so as to cause further heating and moving of the coal, the further heating being carried out in a uniform and gentle manner. At the end of the pipe the coal and carrier gas are separated and the coal is recovered while the waste gas are recycled into a blower and therefrom into the vertical flash drying pipe with a branch leading part of the recycle gas into a mixing chamber with the combustion gases so as to lower the temperature of the combustion gases when the same are passed into the pipe.
    • 焦化煤通过将热载气通过一般垂直的闪蒸干燥管预热和干燥,然后将粉碎的煤通过相同的管道,载气以流速吹送,以使煤在管中向上移动, 管道的中点是将热燃气体和另一热废气管线分支的另外的热循环气体混合到管道中,以进一步加热和移动煤,进一步加热以均匀且平缓的方式进行 方式。 在管道的末端,煤和载气被分离并且煤被回收,而废气被再循环到鼓风机中并且从而进入垂直的闪蒸干燥管中,其中分支引导部分的再循环气体进入混合室 燃烧气体,以便当其通入管道时降低燃烧气体的温度。
    • 54. 发明授权
    • Method of operating coke ovens
    • 操作焦炉的方法
    • US4064017A
    • 1977-12-20
    • US597917
    • 1975-07-21
    • Kurt-Gunther BeckWolfgang RohdeDieter StalhermVolker Kolitz
    • Kurt-Gunther BeckWolfgang RohdeDieter StalhermVolker Kolitz
    • C10B21/20C10B57/00C10B21/10
    • C10B21/20
    • A cokable substance such as coal is admitted into a coking chamber. A quantity of heat which is sufficient to cause coking of the cokable substance is supplied to the chamber during preselected time intervals within the coking period in which coking of the cokable substance progresses in response to the supply of heat. On the other hand, during other time intervals within the coking period in which coking of the cokable substance is essentially unaffected by the supply of heat, the quantity of heat supplied to the chamber is reduced to a level below that required to sustain coking of the cokable substance during the preselected time intervals. In this manner, savings in energy may be realized. The supply of heat to the chamber during those time intervals in which coking of the cokable substance is unaffected by the supply of heat may be discontinued completely.
    • 可燃物质如煤炭进入焦化室。 足以引起可溶性物质焦化的热量在焦化期间内的预选时间间隔内供应到室内,在该焦化期间,可溶性物质的焦化响应于供热而进行。 另一方面,在可焦化物质的焦化基本上不受供热影响的焦化期间内的其它时间间隔内,供给到室的热量降低到低于维持焦化所需的热量 在预选的时间间隔内的可卡因物质。 以这种方式,可以节省能源。 在可燃物质的焦化不受热量的影响的那些时间间隔期间,可以完全停止在室中供应热量。
    • 58. 发明申请
    • ION EXCHANGER MOULDED BODY AND METHOD FOR PRODUCING SAME
    • 离子交换器成型体及其制造方法
    • US20110206569A1
    • 2011-08-25
    • US13126889
    • 2009-10-30
    • Wolfgang RohdeVeronika Wloka
    • Wolfgang RohdeVeronika Wloka
    • B01J39/20C08J9/26B01J8/02
    • B01J20/28042B01J19/2485B01J20/26B01J20/261B01J20/2803B01J20/327B01J39/20B01J41/14B29C64/165B33Y10/00B33Y80/00
    • Organic polymer moldings with ion-exchanger properties or with adsorber properties are produced by means of a powder-based rapid-prototyping process in which a pulverulent organic polymer starting material or starting material mixture is applied in a thin layer to a substrate and then, at selected sites of this layer, is subjected to admixture of a binder and of any necessary auxiliaries, or is irradiated or otherwise treated, so that the powder becomes bonded at these sites, as a result of which the powder becomes bonded not only within the layer but also to the adjacent layers, and this procedure is repeated until the desired shape of the molding has been replicated completely in the resultant powder bed, and then the powder not bonded by the binder is removed, so that the bonded powder is retained in the desired shape, where the starting material itself has the ion-exchanger properties or adsorber properties, or appropriate functionalization of the molding takes place after the shaping process.
    • 具有离子交换性质或具有吸附剂性质的有机聚合物模制品通过基于粉末的快速成型方法生产,其中将粉末状有机聚合物起始材料或原料混合物以薄层施加到基材上,然后在 对该层的选定部位进行粘合剂和任何必需的助剂的混合,或者进行照射或以其他方式处理,使得粉末在这些部位粘结,结果粉末不仅在层内 而且还到相邻的层,并且重复该过程,直到在所得粉末床中完全复制了所需形状的模制物,然后除去未被粘合剂粘合的粉末,使得粘合的粉末保留在 所需的形状,其中原料本身具有离子交换性质或吸附剂性质,或模塑的适当官能化发生在形成后 过程。