会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 14. 发明专利
    • ERROR CORRECTION SYSTEM
    • JPH02150927A
    • 1990-06-11
    • JP30215588
    • 1988-12-01
    • HITACHI LTD
    • KOBAYASHI SHIGEOKOMORI KAZUHIKOKAWASHITA TOMOYOSHITASAKA HIROTAKATSUCHIDA HACHIO
    • G06F11/10
    • PURPOSE:To improve the reliability of a error correction system without deteriorating the availability of a memory by deciding the past errors via a comparator and therefore correcting the errors within a range where the error correction rate is kept under a level allowable with the system. CONSTITUTION:In a normal mode a data control part 25 prevents an error detection/correction control part 15 from correcting errors. Thus the part 15 is limited just to detect the errors, and the read data on the reception data read into an A data buffer 14 is set at a B data buffer 21. When an error is detected, the part 25 outputs an error correction grant command 25a with an error correction mode set. Then the data is read again and the data obtained after correction of the error is set at the buffer 14 and a C data buffer 22 respectively. Then the data on both buffers 21 and 22 are compared with each other by a comparator 23. When a burst error having the bits less than the prescribed number of bits is decided, the data on the buffer 22 is handled as the data undergone the correct error correction. While the other data undergo the error processes. Thus it is possible to improve the system reliability without deteriorating the memory availability.
    • 16. 发明专利
    • MULTIPLEX INDEX ORDER FORMATION FILE
    • JPS61228537A
    • 1986-10-11
    • JP6894685
    • 1985-04-03
    • HITACHI LTD
    • NISHIO NAOKOTSUCHIDA HACHIO
    • G06F12/00
    • PURPOSE:To perform the file opening process in a short period by providing the control information on the position and length of of index keys and the index areas into a file area and to perform the control just with a single file label. CONSTITUTION:A file label 1 of a file structure contains the file name, the file type and the area information showing the start and the end of a file area. Then a multiplex index order formation file is defined when the file type indicates a character M. When the file type shows M, the control information 2 is provided to an area shown at the beginning of the file area. Then a main key index part 3 and subkey (1) index part 4-(8) index part 11 which are defined by the information 2 are arrayed successively. The part 3 contains the data record and the index part of the main key; while the parts 4-11 contain the no-key index parts including no data record. Thus the file opening process is performed in a short time.
    • 17. 发明专利
    • Magnetic disk control system
    • 磁盘控制系统
    • JPS58207160A
    • 1983-12-02
    • JP9024482
    • 1982-05-27
    • Hitachi Ltd
    • TSUCHIDA HACHIO
    • G11B27/10G06F3/06
    • PURPOSE: To decrease the distance required for accessing and then to reduce the revolution queuing time, by calculating a middle sector address from the start and final sector address and storing the calculated sector address in the form of the bit information.
      CONSTITUTION: The sector start and final addresses to which an access is given are written to registers 10 and 11. A process sector register 13 turns on only the bit that corresponds to an access subject address after turning off all bits. A magnetic disk is read to check whether the bit of the register 13 corresponding to the read-out sector address is turned on or not. If this bit is on, the data is transferred by a DMA. After this transfer is over, the bit of the register 13 is turned off. It is possible to start reading at any sector when the data is read out of the continuous sectors.
      COPYRIGHT: (C)1983,JPO&Japio
    • 目的:通过从起始和最终扇区地址计算一个中间扇区地址,并以位信息的形式存储计算的扇区地址,减少访问所需的距离,然后减少旋转排队时间。 构成:给予寄存器10和11的扇区起始地址和最终地址被写入寄存器10和11.处理扇区寄存器13在关闭所有位之后仅接通对应于访问对象地址的位。 读取磁盘以检查对应于读出扇区地址的寄存器13的位是否被接通。 如果该位为ON,则数据由DMA传输。 在该传送结束之后,寄存器13的位被关闭。 当从连续扇区读出数据时,可以在任何扇区开始读取。