会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 1. 发明公开
    • Controller for vehicular lamp
    • SteuerungfürFahrzeuglampe
    • EP2200406A2
    • 2010-06-23
    • EP09178666.5
    • 2009-12-10
    • Koito Manufacturing Co., Ltd.
    • Matsui, KotaroSugiyama, TakaoKitagawa, Takayoshi
    • H05B33/08B60Q11/00B60Q1/00
    • H05B33/0887H05B33/0848
    • To reduce manufacturing costs by suppressing a ground fault current, a controller for a vehicular lamp includes an inverting converter 2 for supplying power to LEDs 21-1 to 21-n, and a current detection unit 3 that includes a shunt resistor Rs connected serially to the LEDs 21-1 to 21-n and detects an LED driving current flowing through the LEDs 21-1 to 21-n. The current detection unit 3 includes a shunt resistor Rs' connected serially to the LEDs 21-1 to 21-n via the shunt resistor Rs, and a bypass section 4. The bypass section 4 includes an NMOS transistor 10 connected parallel to the shunt resistor Rs' and a Zener diode ZD1 that causes the NMOS transistor 10 to turn off when a ground fault occurs at a positive polarity output side or a negative polarity output side of the inverting converter 2.
    • 为了通过抑制接地故障电流来降低制造成本,用于车灯的控制器包括用于向LED 21-1至21-n供电的反相转换器2和电流检测单元3,其包括串联连接到 LED 21-1至21-n,并且检测流过LED 21-1至21-n的LED驱动电流。 电流检测单元3包括经由分流电阻器Rs与LED 21-1至21-n串联连接的分流电阻器Rs'和旁路部分4.旁路部分4包括并联于分流电阻器的NMOS晶体管10 Rs'和齐纳二极管ZD1,当在反相转换器2的正极性输出侧或负极性输出侧发生接地故障时,使NMOS晶体管10截止。
    • 2. 发明公开
    • Vehicle lighting control device
    • Fahrzeugbeleuchtungssteuerungsvorrichtung
    • EP2096900A1
    • 2009-09-02
    • EP09153665.6
    • 2009-02-25
    • KOITO MANUFACTURING CO., LTD
    • Matsui, KotaroKitagawa, Takayoshi
    • H05B33/08
    • H05B33/0818Y02B20/347
    • A vehicle lighting control device includes a switching unit to perform ON/OFF control of a driving current supplied to a semiconductor light source depending on a light control signal; and a constant-current control unit to perform constant-current control on the driving current. The constant-current control unit includes a switch unit to perform ON/OFF control of the switching unit; and a signal-maintaining unit to provide a voltage signal corresponding to the driving current to the switch unit when the switching unit performs ON control, and to provide continuously the voltage signal to the switch unit when the switching unit performs OFF control.
    • 车辆照明控制装置包括切换单元,用于根据光控制信号对提供给半导体光源的驱动电流进行ON / OFF控制; 以及对驱动电流进行恒定电流控制的恒流控制单元。 恒流控制单元包括用于执行开关单元的ON / OFF控制的开关单元; 以及信号保持单元,用于当切换单元执行ON控制时向开关单元提供与驱动电流相对应的电压信号,并且当切换单元执行OFF控制时,向开关单元提供电压信号。
    • 3. 发明公开
    • Light source lighting circuit and lamp system for vehicle
    • Lichtquellenbeleuchtungsschaltung und LampensystemfürFahrzeug
    • EP2416626A2
    • 2012-02-08
    • EP11176694.5
    • 2011-08-05
    • Koito Manufacturing Co., Ltd.
    • Matsui, Kotaro
    • H05B33/08
    • H05B33/089H05B33/0887
    • A lighting circuit includes: a countercurrent prevention unit including a first control terminal and a second control terminal, the countercurrent prevention unit transmitting a first current or a second current; and a current controller including: a common terminal connected to the first control terminal and the second control terminal; and a switching terminal connected to the first control terminal, the current controller providing a first driving current or a second driving current from the common terminal to the light source. The countercurrent prevention unit further includes: a first rectifier, wherein voltage at the first control terminal is provided to the switching terminal through the first rectifier; a first P-FET provided between the first control terminal and the common terminal; a second P-FET provided between the second control terminal and the common terminal; and a second rectifier provided between the second P-PET and the common terminal.
    • 照明电路包括:逆流防止单元,包括第一控制端子和第二控制端子,逆流防止单元发送第一电流或第二电流; 以及电流控制器,包括:连接到所述第一控制端子和所述第二控制端子的公共端子; 以及连接到第一控制端子的开关端子,电流控制器从公共端子向光源提供第一驱动电流或第二驱动电流。 逆流防止单元还包括:第一整流器,其中第一控制端子处的电压通过第一整流器提供给开关端子; 设置在所述第一控制端子和所述公共端子之间的第一P-FET; 设置在第二控制端子和公共端子之间的第二P-FET; 以及设置在第二P-PET和公共端子之间的第二整流器。