会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 2. 发明授权
    • Method of making a porous carbon cathode, a porous carbon cathode so
made, and electrochemical cell including the porous carbon cathode
    • 制造多孔碳阴极的方法,如此制造的多孔碳阴极和包括多孔碳阴极的电化学电池
    • US4514478A
    • 1985-04-30
    • US640265
    • 1984-08-13
    • Michael BinderEric R. PetersenCharles W. Walker, Jr.William L. Wade, Jr.Sol Gilman
    • Michael BinderEric R. PetersenCharles W. Walker, Jr.William L. Wade, Jr.Sol Gilman
    • H01M4/96H01M6/14
    • H01M4/96H01M6/14Y10T29/49108Y10T29/49115
    • A porous carbon cathode for use in an electrochemical cell is made by wetg the carbon black with a 1:1 to 1:3 mixture of isopropyl alcohol:water, adding a binding agent thereto, smearing the resulting stiff paste on a thin expanded metal screen and pressing and rolling to the desired thickness, drying the cathode sheet in a vacuum oven at about 100.degree. C. for one hour while a weight is placed above and below the cathode sheet which is sandwiched between two pieces of blotting paper, the total weight applied being sufficient for the cathode to retain structural integrity, removing the weight and blotting papers and inserting the cathode sheet in an elevated drying oven at about 280.degree. C. for about one hour, and cooling the cathode sheet between blotting paper, repressing and rolling. Cathodes prepared by this method appear structurally strong, maintain their physical integrity with a minimum of cracking and flaking, and do not crumble when cut. The porous carbon cathode is particularly advantageous when included in a lithium sulfuryl chloride cell, but can be used in any system requiring porous carbon cathodes.
    • 用于电化学电池的多孔碳阴极是通过用1:1:1:1:1:1:2的异丙醇:水的混合物润湿炭黑制成的,向其中加入粘结剂,将所得的硬糊涂抹在薄的金属扩孔 并压制成所需的厚度,在真空烘箱中在约100℃下干燥阴极片1小时,同时将重量置于夹在两片吸印纸之间的阴极片的上下,总重量 施加足以使阴极保持结构完整性,去除重量和吸印纸并将阴极片在约280℃的升高的干燥炉中插入约1小时,并在吸印纸,压制和轧制之间冷却阴极片 。 通过这种方法制备的阴极在结构上很强,在最小的开裂和剥落下保持其物理完整性,切割时不会破碎。 当包含在锂磺酰氯单元中时,多孔碳阴极是特别有利的,但可以用于需要多孔碳阴极的任何系统中。
    • 9. 发明授权
    • Method of making a high rate carbon cathode
    • 制造高倍率碳阴极的方法
    • US4303604A
    • 1981-12-01
    • US140369
    • 1980-04-14
    • Sol Gilman
    • Sol Gilman
    • H01M4/96B29D9/08
    • H01M4/96
    • A high rate carbon cathode is made by mixing a carbon powder having a sure area of about 1000 square meters/gram with polytetrafluoroethylene and a sufficient amount of water to form a coherent mixture. The mixture is applied to an electrically conductive screen; the cathode formed while wet to an intermediate thickness, the cathode vacuum dried at about 100 degrees C., and the cathode cold compressed to obtain a final electrode porosity of greater than 80 percent. The cathode can be used in a lithium primary cell using a solution of an inorganic lithium salt in sulfuryl chloride as the electrolyte.
    • 通过将具有约1000平方米/克的表面积的碳粉与聚四氟乙烯和足量的水混合以形成粘性混合物来制备高速碳阴极。 将混合物施加到导电屏幕上; 阴极在湿润至中间厚度的同时形成,阴极在约100℃下真空干燥,并将阴极冷压缩以获得大于80%的最终电极孔隙率。 阴极可以使用无机锂盐在磺酰氯作为电解质的溶液在锂原电池中使用。