会员体验
专利管家(专利管理)
工作空间(专利管理)
风险监控(情报监控)
数据分析(专利分析)
侵权分析(诉讼无效)
联系我们
交流群
官方交流:
QQ群: 891211   
微信请扫码    >>>
现在联系顾问~
热词
    • 71. 发明授权
    • Active balun circuit for single-ended to differential RF signal conversion with enhanced common-mode rejection
    • 主动平衡 - 不平衡转换电路,用于单端到差分RF信号转换,具有增强的共模抑制
    • US06922108B2
    • 2005-07-26
    • US09877900
    • 2001-06-08
    • Jenshan Lin
    • Jenshan Lin
    • H03H11/32H03F3/45
    • H03H11/32
    • An active balun circuit is provided for single-ended to differential RF signal conversion with enhanced common-mode rejection which suppresses common mode signal and which achieves phase and amplitude balance without sophisticated tuning or compensation methods. The circuit has a single-ended input and balanced output with phase and amplitude balance error less than 2° and 1.2 dB, respectively, measured from 1.5 GHz to 1.8 GHz at 5V supply. When supply voltage drops down to 1.5V, its phase and amplitude balance error remains within 5° and 2 dB, respectively. The circuit achieves a balanced output via an output network which behaves as an impedance matching network for differential mode signal and is grounded for common mode signal. As a result, common mode signal is suppressed and 180-degree phase balance at output is achieved. The circuit has high-linearity (P1 dBin=5 dBm, IIP3=16.6 dBm) and low residual phase noise (
    • 提供了一种主动平衡 - 不平衡转换电路,用于单端到差分RF信号转换,具有增强的共模抑制,可抑制共模信号,无需复杂的调谐或补偿方法即可实现相位和幅度平衡。 该电路具有单端输入和平衡输出,相位和幅度平衡误差分别小于2°和1.2 dB,在5V电源下从1.5 GHz到1.8 GHz测量。 当电源电压降至1.5V时,其相位和幅度平衡误差分别保持在5°和2 dB之内。 该电路通过输出网络实现平衡输出,该输出网络作为差分模式信号的阻抗匹配网络,并为共模信号接地。 结果,抑制了共模信号,并且实现了输出时的180度相位平衡。 该电路具有高线性度(在 = 5dBm,IIP3 = 16.6dBm中为P1dB <! - SIPO - >)和低残留相位噪声(在100kHz及以上<-155dBc / Hz) 用于基站接收机应用的LO和平衡混频器之间的主动平衡 - 不平衡转换/缓冲放大器。
    • 72. 发明授权
    • Component operating with bulk acoustic waves, and having asymmetric/symmetrical circuitry
    • 组件用体声波操作,并具有不对称/对称电路
    • US06917261B2
    • 2005-07-12
    • US10728462
    • 2003-12-05
    • Michael Unterberger
    • Michael Unterberger
    • H03H9/00H03H9/58H03H9/205H03H9/54H03H11/32
    • H03H9/589H03H9/0095H03H9/584
    • A component operating with bulk acoustic waves has two Bulk Acoustic Wave (BAW) resonators that are stacked and are acoustically coupled to one another, with a first resonator being connected to an asymmetric port, and a second resonator being connected to a symmetrical port. The acoustic coupling is provided by a partially permeable coupling layer system, which has an alternating sequence of at least two λ/4 mirror layers with different acoustic impedance. The coupling layer system furthermore has a compensation layer, which has an approximate thickness of λ/8. The compensation layer according to the invention makes it possible to match any discrepancy in the phase difference (which is caused by reflections on the mirror layers) from the predetermined 180° between the connections of the symmetrical port to approximately 180°.
    • 使用体声波操作的部件具有堆叠并彼此声学耦合的两个体声波(BAW)谐振器,第一谐振器连接到非对称端口,第二谐振器连接到对称端口。 声耦合由部分可渗透的耦合层系统提供,该系统具有至少两个具有不同声阻抗的λ/ 4镜层的交替序列。 耦合层系统还具有补偿层,其具有λ/ 8的近似厚度。 根据本发明的补偿层使得可以将对称端口的连接之间的预定180°的相位差(由反射镜层上的反射引起的)的任何差异与约180°的连接相匹配。
    • 79. 发明授权
    • Floating driver circuit and a device for measuring impedances of
electrical components
    • 浮动驱动器电路和用于测量电气部件阻抗的装置
    • US4795962A
    • 1989-01-03
    • US93845
    • 1987-09-04
    • Kouichi YanagawaKazuyuki Yagi
    • Kouichi YanagawaKazuyuki Yagi
    • G01R27/02G01R27/00H03H11/32
    • G01R27/00
    • A floating driver circuit. A power supply is connected through a signal source to an amplifier's input terminal. The power supply is also connected to a pair of power supply terminals of the amplifier, via at least one resistor for each power supply terminal, so that direct current flows from the power supply into the power supply terminals. Further, at least one capacitor is connected to each power supply terminal. A cable, preferably coaxial, has first and second conductors. The first conductor is connected to a signal output terminal of the amplifier. The second conductor is connected to the power supply terminals through the capacitors. A pair of these circuits is combined at opposite ends of an electrical component to enable measurement of the impedances thereof.
    • 一个浮动驱动电路。 电源通过信号源连接到放大器的输入端。 电源还通过用于每个电源端子的至少一个电阻器连接到放大器的一对电源端子,使得直流电流从电源流入电源端子。 此外,至少一个电容器连接到每个电源端子。 优选地,同轴的电缆具有第一和第二导体。 第一导体连接到放大器的信号输出端。 第二导体通过电容器连接到电源端子。 一对这些电路在电气部件的相对端组合,以便能够测量其阻抗。